Friday, June 30, 2017

PTU Relaxing on the Beach


This tut was written June 29, 2017 for those with a basic knowledge of psp.
I am using the awesome artwork of  Keith Garvey
Tube is called Tanned.
You need a license to use this art work. Please do not use without a license.
 You can find this art at his store  HERE

Supplies Needed
I used PSPX...but any of them should work.
Scrap Beach Fun by PurpleDream Scraps  HERE
This kit is Awesome, 55 Elements and 08 Papers,
ready for your summer beach fun tagging needs.
Check out her blog HERE
Dragonfly Mask 0018  HERE
Check out the rest of the blog HERE
Filter
xero-SoftMood and Clarity
Font of Choice, I used Heaven Matters

Drop shadow is usually V-2 H-2 Black, 50, 5, use what you prefer.
Let's get started
*Remember to add your drop shadow as you go along*

Open a new image 800 x 800, paste paper 7, apply your mask, delete, merge group,
resize later to fit your tag.
Paste paper 8, apply the same mask, delete, merge group, take your Pick tool,
hold the square at one of the top ones, hold your shift key and drag down on
one side, then the other side until it is as flat as you like, duplicate, mirror,
adjust them to your liking.
Resize element 24 to 85%, paste below one of the sand paper layer.

Resize element 45 to 95%, paste below the sand paper layer.

Paste your tube at the bottom where you like.

Paste element 48 below the water layers, duplicate, resize to 50%, paste
on one side, duplicate, mirror, adjust to your liking.

Resize element 27 to 50%, paste behind the tube on the right.
Resize element 50 to 25%, paste in front of the tube where you like.
Resize element 20 to 40%, paste on the right behind the castle layer.
Resize element 16 to 40%, paste on the left below the foot of your tube.
Resize element 11 to 30%, paste on the left on the sand, duplicate
move more to the right behind the tube.
Resize element 40 to 20%, paste on the right by the tube.

Paste element 46, below the rock on the right, mirror, move down more on the left.
Paste element 47 on the mask layer, adjust to your liking.

Resize element 42 to 30%, paste on the left on the greenery, duplicate, move to
the right below the starfish layer.
Resize element 33 to 30%, place on the sand where you like, duplicate, move
over a bit.

Resize element 8 to 25%, mirror, place behind the small rock on the left.
Resize element 51 to 60%, paste at the upper left above the rock layer.

Resize element 4 to 15%, mirror, paste above the rock on the left and down some.
Resize element 2 to 20%, paste below the water by the castle on the right.
Resize element 5 to 15%, paste on the mask layer in the opening of the rock.

Resize element 18 to 50%, paste on the mask layer and down so just some of it
shows in the opening of the rock, duplicate, move to the left past the
rock edge and down some, duplicate again, mirror, adjust on the right side.

Resize element 10 to 40%, mirror, place on the left on the smaller rock.
Resize element 17 to 40%, paste below the tube at the bottom by her knees.
Resize element 28 to 20%, place above the rocks at the bottom.
Resize element 3 to 25%, paste on the rock at the top more.


Add any other elements you would like to add.

Crop your tag to be sure no stray shadows are on the edges of your tag.
Close off any background you may have used, resize first then, duplicate, go to
Adjust, Blur, Gaussian blur, number on 4, change
the blend mode to Screen. 
Apply the xero filter-Soft Mood three times, then Clarity once.
add your copyrights and name.

That's it
Hope you enjoyed doing my tut.



No comments:

Post a Comment